Acctek / HomePage / News / Industry news

Common troubleshooting methods for CO2 laser cutting machine

Updatetime: 2021-07-10 16:04View:
Laser cutting machine is currently a relatively common engraving processing equipment, which is widely used in advertising industry, clothing industry, decoration processing industry, etc. CO2 laser engraving machine has the characteristics of fast speed and convenient operation, which is loved by many manufacturers.
When the CO2 laser engraving machine has been working for a long time, it is inevitable that the machine malfunctions. Today AccTek has compiled the troubleshooting methods for the common faults of the CO2 laser engraving machine for you. I hope it will be helpful for you to operate the machine.
(1) The laser tube is on and the voltmeter has instructions
① Abnormal light output and heat in the light-guiding joints are common when the light-guiding joints are loose and the laser tube is not installed properly.
Inspection method: same light correction. Elimination measures: replace or adjust the light guide section, correct the light path.
②Laser power drop is common in laser tube aging.
Check: Check the voltage regulator with a multimeter and check the working voltage of the laser tube with a high-voltage meter.
Treatment: Replace the aging laser tube and replace the damaged components.
(2) The laser tube is not bright
①The indication of the voltmeter is common when the power supply line has an open circuit. Poor contact with foot switch or manual switch.
Check: Use a multimeter to measure. Treatment: repair or replace.
②Voltmeter has no indication. Common fuse is broken, or the circuit is open.
Check the measurement with a multimeter. Treatment: Replace the fuse, or connect the circuit.
③The power indicator does not light up, usually the fuse is broken, the incoming line is poorly connected, the indicator circuit is bad or the indicator is broken.
Check: check the fuse, check the power supply line, and check the indicator circuit.
Treatment: Replace the fuse, repair the wire and replace the indicator light.
④Continuously burning the fuse is usually caused by a short circuit in the machine and serious dirt in the machine.
Check: Check the wires step by step, mostly because the high voltage part has a short circuit. Treatment: Repair the short circuit and remove the dirt.
⑤There is discharge sound or arc light in the machine. It is common that there is dust, water or air humidity and corrosive gas in the machine.
Check: Observe the discharge point in a dark place. Treatment: Remove dust, water, etc., and change the working environment.
⑥The laser output is unstable. It is seen in the poor contact inside the machine, and there are slight intermittent short-circuit points in the machine.
Check: Check the line level by level. Treatment: Replace the wire, re-weld the wire end, and clean it.
Precautions
(1) If the whole machine is found to be discharged due to humidity or other reasons during adjustment and use, it should be shut down immediately for maintenance.
(2) The laser machine can work continuously for 4 hours at low current, and the use time can be shortened as appropriate at high current.
(3) The chassis should be grounded, and the power cord should be single-phase three-wire.
(4) Please place the light guide joint arm in a dry box when not in use to prevent the lens from becoming moldy.
(5) Cut off the power supply and carry out high-voltage discharge during maintenance to ensure safety.
The above are the common troubleshooting methods of CO2 laser engraving machine organized by AccTek for you. If you encounter other problems when using the laser machine, you can also consult online for free; if you need to buy a new machine or machine accessories, you can Learn about product prices online. Hope to help you use the machine.

Get a Free Quote Now!

Jinan AccTek Machinery

Headquarters: 3-1007, Minghu Plaza, No. 777 Minghu West Street,Jinan City / Branch:  A2-1-1802, Hanyu Jingu, High-tech Zone, Jinan City

Factory:  No. 3 Zone A, Lunzhen Industrial Zone,Yucheng City , Shandong Province


Copyright © Jinan AccTek Machinery Co.,Ltd