Acctek / HomePage / News / Q&A
What is the daily maintenance the cnc router?
Updatetime: 2021-10-11 14:05 View:
As an CNC Router manufacturer, I often encounter customers asking about the daily maintenance of the machine. The correct daily maintenance can not only improve the working efficiency of the cnc engraving machine, but also extend the service life of the cnc router.
The daily maintenance of the machine is a simple but very important thing. This post introduces the maintenance methods of the cnc router from many aspects, and hopes to help you better use the cnc engraving machine.
CNC router

1. Daily maintenance of the CNC router spindle

It is recommended that the continuous running time of the CNC router be controlled within 10 hours a day. The cooling water should be kept clean, and the water pump should be able to work normally. The water cooling spindle must not suffer from water shortage. And at the same time, pay attention to regularly replacing the cooling water to avoid excessive water temperature. When the spindle heats up, it is necessary to stop the operation of the CNC router, and the cooling water and cooling water pump should be checked in time to avoid damage to the spindle of the machine.
If the area where you work is hotter, you can choose to use a chiller, so that the cooling water can continue to maintain a low temperature state. When the temperature is too low in winter, we can replace the water in the water tank with antifreeze so that the machine can be used normally.
The air cooling spindle should be checked on time for the cooling fan operation. If the temperature of the spindle is too high or the fan fails, it should be shut down for maintenance in time.
After one day's operation is completed, first remove the engraving knife and let the spindle chuck lock nut in a relaxed state. This is helpful to prolong the service life of the spindle chuck.

2. Daily cleaning of CNC machine

After each use of the CNC router, do not forget to clean it. There may be dust on the transmission system, so please pay attention to it. Then we start to clean the worktable surface, which can be cleaned with a brush; note that it is usually best not to accumulate debris on the work surface to avoid deformation of the platform.
Regularly clean the dust in the electrical box (note: be sure to cut off the power first, and wait until the monitor does not display and the indicator light of the loop power supply has gone out before proceeding). Check whether the wiring terminals and the screws of each component are loose to ensure the safe and reliable use of the circuit. If the cnc router needs a computer to run, it needs to clean the inside of the computer. Excessive dust in the computer will cause the computer to malfunction, and signal errors will cause the cnc router to be misaligned.
Maintenance of CNC

3. Lubrication system of CNC router

Lubricate the transmission system regularly every week, the engraving machine equipped with manual lubrication needs manual lubrication once in 3-5 days. Or if you need it, you can also buy a woodworking engraving machine with an automatic lubrication system. The engraving machine with automatic lubrication system only needs to set the interval time and lubrication time to perform automatic lubrication.
If the machine is not used for a long period of time, it should be lubricated regularly (weekly) to ensure the flexibility of the transmission system.
 
Regarding how to maintain the CNC engraving machine, the above is some relevant knowledge that ACCTEK has compiled for you. But when the machine fails, if you can't get a solution, you need to contact the maintenance personnel or the seller's after-sales personnel for professional maintenance in time.
Good maintenance of the CNC router can ensure that the machine provides a longer use time and stable engraving efficiency for the workshop. The ACCTEK's product videos can be seen on Facebook and YouTube. Search for AccTek CNC on Facebook and AccTek China on Youtube. You can learn more about CNC knowledge.
Facebook and Youtobe

Get a Free Quote Now!

Jinan AccTek Machinery

Headquarters: 3-1007, Minghu Plaza, No. 777 Minghu West Street,Jinan City / Branch:  A3-4-905, Hanyu Jingu, High-tech Zone, Jinan City

Factory:  No. 3 Zone A, Lunzhen Industrial Zone,Yucheng City , Shandong Province( Postal code 251200)


Copyright © Jinan AccTek Machinery Co.,Ltd Power by DedeCms