Acctek

Acctek

How to deal with the slag generated during laser cutting

When the laser cutting machine cuts, as long as the correct operation is followed, there will not be any major problems, and the cutting effect is better. When using this equipment for processing and cutting,
    How to deal with the slag generated during laser cutting?
    When the laser cutting machine cuts, as long as the correct operation is followed, there will not be any major problems, and the cutting effect is better. When using this equipment for processing and cutting, if there are burrs and dregs, you must pay attention. The key is to find out the cause of the problem and solve it in time.
    How are glitches produced?
    In fact, burrs are excessive residual particles on the surface of metal materials. When the laser cutting machine processes the workpiece, the energy generated by the laser beam irradiating the surface of the workpiece makes the surface of the workpiece evaporate to achieve the purpose of cutting. But there is a device we need to pay attention to, that is gas.
    After the gas is vaporized on the irradiated surface of the workpiece, the slag on the surface of the workpiece is blown off. If gas is not used, the slag will form burrs and adhere to the cutting surface after cooling. Therefore, the purity of the gas should be high. You can switch to a higher-quality natural gas supplier. The purity of the gas is very important. Do not use cylinder gas, because after two fillings, the purity is not good and the gas is wasted.
    Another reason is the quality problems and parameter setting factors of the equipment itself, so when customers buy laser cutting machines, they should let experienced operators debug the equipment. Therefore, it is necessary to adjust the cutting parameters and the cutting speed of the air pressure flow focal length. It is necessary to adjust the cutting speed several times. The parameters provided by this machine cannot cut high-quality workpieces.
    If a material has burrs, the material may be defective in quality. The more burrs, the lower the quality.
    Generally speaking, when the laser cutting machine has burrs, it can be checked and solved from the following aspects:
    1. The output power of the laser cutting machine is insufficient.
Solution: Check whether the laser cutting machine is working normally. If there is any abnormality, timely repair and maintenance are required. If it is normal, check whether the output value is correct.
    2. The up and down position of the beam focus is deviated.
Solution: Adjust the focus position according to the offset position.
    3. The gas purity of the cutter is not enough.
Solution: ventilation.
    4. The wire cutting speed of the cutting machine is too slow.
Solution: Adjust the wire cutting speed in time.
    5. The laser beam of the tool is offset.
Solution: Debug focus and adjust in time
    laser cutting machine is a kind of precision cutting machine. Data errors often lead to abnormal operation. Therefore, strict requirements should be required in the work to reduce errors.
    Some minor problems are the factors that cause burrs and slag in the laser cutting machine, so we hope to solve these problems when facing this problem.
laser cutter

    Laser cutting machines are popular products in the leather cutting industry.
    Leather can be seen everywhere, whether it is leather or artificial leather, from leather shoes to leather clothing, car cushions, etc. With the advancement of science and technology, leather cutting equipment is constantly updated. At present, non-metal laser cutting machines have become popular products in the leather cutting industry.
    Non-metal cutting machines are mainly used for materials such as leather, cloth, denim velvet, and pure cotton silk. It can automatically feed materials, greatly improve production efficiency, and is suitable for small batches and diversified orders. This demand requires manufacturers to respond quickly to the demand market and deliver in time.
    Non-metallic feature laser cutting machine:
1. Large-size laser cutting is smooth and delicate, which can meet the cutting processing requirements of the entire cloth.
2. Fully automatic feeding and receiving, saving time and improving work efficiency.
3. The feeding system adopts the B-shaped belt table, and the crawler automatically feeds, so that the processed products can move freely on the worktable.
laser cutter

Jinan AccTek Machinery Co.,Ltd

Mail:sales@acctekgroup.com

Tel:13964085002

WhatsApp:139085002

Inquiry

Contact Us

Jinan AccTek Machinery Co.,Ltd

Headquarters : Headquarters:3-1007, Minghu Plaza, No. 777 Minghu West Street,Jinan City

Branch : Office Branch:A3-4-905, Hanyu Jingu, High-tech Zone, Jinan City

Factory : North Plant, Dafan industry park, South Pingan Rd.,Changqing Dist., Jinan City,China

Email : sales@acctekgroup.com

tel +086-0531-86160023

Copyright © 2021 Jinan AccTek Machinery Co.,Ltd